The siren will emit 2 short arm "chirps" to indicate that the system is fully armed. Press the arming button (refer to multi- car operation to determine button function) on the remote control transmitter.
#Code alarm pro 3500 manuals
NOTE: Technical support, parts, user manuals (not shown on this FAQ), accessories, or repairs are either limited or NOT available for discontinued models.Remote Operation for the Code Alarm PRO3000 AlarmĪrming the System: Turn the ignition key off and exit the vehicle. Thank you for your inquiry - Audiovox values our customers and though this product is no longer in production nor does it qualifiy for warranty or repair due to the age of the product, limited support information may be available through our FAQ Database and/or Customer Service.īefore you proceed check this and other answers related to your product by searching with the Model Number of your product from the Search Box above. This cycle is repeated five times to draw extra attention to the vehicle while keeping the vehicle armed and alert. If a thief returns to try again, he returns to an armed vehicle.Ĭontinuous Open Door Monitor: If a potential thief attempts a break-in and leaves the vehicle door ajar, alarm sounds for one minute, then turns off.
Since new codes do not have to be specially ordered, your vehicle will not go unprotected.Īutomatic Rearm After Trip Cycle: If alarm is tripped, siren sounds for 60 seconds, then siren stops and system rearms itself. Scan Deterrent: This alarm is designed to prevent any attempt by a thief to disarm your system by electronically scanning your personal transmitter code.Ĭode Learning: Dealer can program system on the spot to learn up to four new transmitter codes should original transmitter be lost or stolen. Import vehicles) or Hood/Trunk was triggered. 4 CHIRPS - Door Sensor was triggered (G.3 CHIRPS - Door Sensor was triggered (Ford vehicles only).2 CHIRPS - Ignition has been turned "ON".To identify what tripped your system push the emergency override button before turning the ignition on.
#Code alarm pro 3500 series
Trip Identification: When you disarm your system, the siren will emit a series of" Chirps", if the alarm was tripped in your absence. This gives you time to exit the vehicle without tripping the alarm.Īudible Alarm Trip Indicator: In addition to the LED indicator blinking fast if the system has been tripped while armed, the siren will "chirp" 4 times, parking light will flash upon disarming the system (if the system has gone through a complete siren cycle) as an audible indication that it was triggered during your absence. Last Door Arming: System waits until the last door on the vehicle is closed, then automatically arms itself. The starter is "locked out" simultaneously with the 2nd arm "chirp".Īutomatic Sensor Bypass: Siren shuts off after 5 repeated sensor trips to prevent any annoyance while the rest of the alarm system remains armed and alert. This immobilizes your vehicle, so a thief cannot start your vehicle even if he's gained entry. Starter Interrupt: When your system is armed, it breaks electrical connection to the vehicle's starter circuit. Vehicle will then be disarmed and you can start the vehicle. Enter the vehicle (siren will activate), turn on the ignition switch, then press the hidden emergency override button. The siren can be turned off before 30 seconds by pressing any button on the remote control transmitter.Įmergency Override Button: Only use the emergency override button if your remote control transmitter is lost or broken. The siren will turn on and remain active for 30 seconds. press both buttons on the remote control transmitter at the same time. Remote Control Panic Button Operation: With the system armed or disarmed. The vehicle can now be started normally.Įmergency Override Button: In the event of a lost transmitter, enter the vehicle, turn on the ignition switch, then press the hidden disarm button to disarm the vehicle. The dash mount status light will turn off. The siren will emit one long "chirp" (about twice the duration of the arm "chirps") to indicate that the system is fully disarmed. The siren will emit the 2nd arm "chirp" 1 second after the entry point is closed.ĭisarming the System: With the system armed, press the disarm button on the remote control transmitter. A single short "chirp" indicates that one of the protected entry points has been left open. Remote Operation for the Code Alarm PRO1000 or PRO1000SX AlarmĪrming the System: Turn the ignition key off and exit the vehicle.
0 kommentar(er)
